[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: (ET) C-185 and Loader



As I am to understand the bent/welded axle is intended to be used with the
front end loader. Also there are heavy duty spindles available for the 
front
end.
I lifted the rear of a full size pickup with my loader. This was
accomplished with the tiller and my father on the rear. I was not moving as
this would have been to much stress on the tractor. Unless your lifting 
lead
or gold you cant fit #500 in the bucket and mulch in not that dense. I know
wet soil can weigh that much but the tractor has a tendency to tilt forward
with an excess of weight.
----- Original Message -----
From: <JeffT softlanding com>
Cc: ET discussion list <elec-trak cosmos5 phy tufts edu>
Sent: Friday, February 18, 2000 8:51 AM
Subject: RE: (ET) C-185 and Loader



Did you see the rear mount bucket they have over there? Might be a better
solution.

I was thinking the snowblower is no lightweight for the front end, but you
have to support the weight of the bucket loader assembly and the contents
of the bucket.

Jeff Tickner
C/S Developer
SoftLanding Systems
603-924-8818 ext 536



                    "Pieter Litchfield"
                    <plitch attglobal net>             To:     "ET
discussion list" <elec-trak cosmos5 phy tufts edu>, "Walter "
                    Sent by:                           <dwfh starlinx com>
                    owner-elec-trak cosmos5 phy        cc:
                    .tufts.edu                         Subject:     RE: 
(ET)
C-185 and Loader



                    02/17/00 08:04 PM






A word of caution  - The ElecTrak really isn't appropriate for heavy
lifting. My E-15 with a  forged or cast iron front axle still snapped a
spindle due to the loads placed  on it by a bucket loader. A knuckle
design that supported the axle both  above and below the front axle stubs
would have been much stronger.   Remember the weight of the loader itself
must be supported as well as the load,  and the E-15, as much as I love it,
was made from off the shelf lawn tractor  parts. The front axle was
appropriately strong for a mower, but not a  forklift. I assume the E-20
may be similar in construction to the  15. I know my E-12 has a bent sheet
front axle that clearly wasn't meant  for lifting.
-----Original Message-----
From:  owner-elec-trak cosmos5 phy tufts edu
[mailto:owner-elec-trak cosmos5 phy tufts edu]On Behalf Of Walter
Sent: Thursday, February 17, 2000 03:23 PM
To: David  Erskine
Cc: elec-trak cosmos5 phy tufts edu
Subject: Re:  (ET) C-185 and Loader


Here is the web address for the loaders: http://www.cadplans.com
I have the plans for the #507. This is a  single arm loader with expected
lifting abilities of #500.
The plans package I got came with a video, plans  and a list of materials
and where to get the whole materials  pre-cut.

It would be very easy to power any of these  units with a 36 volt drive
motor.

Walter
----- Original Message -----
From:  David Erskine
To: Walter
Sent: Thursday, February 17, 2000 11:53  AM
Subject: Re: (ET) C-185 and  Loader

I would be very interested in obtaining a  set of plans/parts source(s) for
a front end loader for a small electric  tractor (Sears). If convenient
would you e-mail me the address,  etc. (Or post it to the electric tractor
group; whichever is most  convenient.)

Thanks, David R.  Erskine
-----Original Message-----
From:  Walter <dwfh starlinx com>
To: elec-trak cosmos5 phy tufts edu  <elec-trak cosmos5 phy tufts edu>
Date:  Wednesday, February 16, 2000 11:28 PM
Subject: (ET) C-185  and Loader


Hi All,

Today I re-attached my bucket loader to my  C-185 (Wheelhorse) (had it on a
E20). I needed to move a few snow piles  from the side of a driveway and
this is much better then a shovel. I was  busy so I let Dad run the loader.
I was a bit unsure as he is used to a  larger 1953 Golden Jubilee Ford
tractor with loader and was not in the  mood for complaints i.e.: its to
small, it's to slow, it's not strong  enough blah blah....

I was also a bit unsure as to the performance  since I have not charged the
batteries since about September of  99.

Well, to say the least Dad was thrilled and  so was I. The batteries did
nicely as did the tractor. I have it set up  with 75 pound wheel weights in
the rear and well with Dad on it there was  more then enough weight to move
snow. He did say in the beginning that his  Ford would have had the job
done in 1/8 the time but was none the less  impressed.

My father was the one who turned me on to the  Elec-trak some years ago and
I have not turned off since. The one counter  point I have always made to
dad and others is there are few alternatives  to the Elec-trak when it come
to versatility.

We all know that to change between a loader,  snow blower, plow, mower,
sickle mower, rototiller is less then 3 minutes.  Plus do hedge trimming,
welding, drilling, sawing in between all of that.

I was sorry that I didn't bring my camera as  it was a sight to see him on
the tractor. I also have to add it took him a  bit to get used to all the
switch flipping i.e.: forward, reverse, PTO  on/off, 2 hydraulic handles,
brake and accelerator. In time he did just  fine.

I was some time ago going to manufacture a  loader for the Elec-trac but
was side lined by DiVoRcE. Never a good word.  There is a company that
sells universal plans for small tractor loaders  that need little
adaptation for the GE/Wheelhorse units. With the plans  they give you
places to buy all the precut materials if you don't have the  shop to make
them yourself. The only thing you would need to make up for  our electric's
is the motor to run the pump. This is accomplished with the  small 36 volt
drive motor from say a E-8.

I have moved 3 times in 4 months and to say  the least I can't find my A**
with my 2 hands. I will search for the web  address and post it here for
anyone interested. I believe that to buy the  kit and plans would have cost
about $800 Don't quote me). You only needed  basic welding skills to build
the unit. They also had plans for a back hoe  that I would love to have.

I will get some pics of the loader on my  C-185 if any one is interested.

Thanks for listening.

Walter

web.starlinx.com/dwfh